Slotted Mini Rail 12mm Glass

Product Code : MINI.RAIL.25.2205.DP

Order Now

PriceFrom: £50.00

Clear

This will also add the following products to your cart:

  • Mini Rail End Cap
  • Wall Bracket for Mini Rail
  • ELITE MINI RAIL Gasket (12mm)

STAINLESS STEEL SLOTTED MINI RAIL (for 12mm Glass)

STAINLESS STEEL MINI RAIL 25 x 21mm GRADE 2205 SATIN POLISHED – FOR 12MM GLASS

A great cost saving solution for frameless balustrade systems. Allows to frameless balustrade without laminated toughened glass meet safety and building requirements by adding a low profile rail with the minimal visual impact. Glass mounted gasket supplied to use with 12mm glass.

The rail is made from a high grade stainless steel known as Grade 2205 Duplex. It is ideal to use in extreme environmental conditions, due to its resistance to corrosion. It is also a very strong product with high tensile strength values.

The small 25 x 21mm square profile allows for a minimal visual impact on your glass balustrade installation. Providing additional strength, keeps frameless glass panels aligned and assures certain balustrade designs meet building regulations, when used with sheets of toughened (un-laminated) glass. No silicone or adhesives needed to secure the rail to the glass.

Weight7 kg
Dimensions50 × 4 × 4 cm
Size

2500mm, 5000mm

Number of Cuts

0, 1, 2, 3, 4, 5, 6, 7, 8

INSTALLATION GUIDANCE
To fix the handrail to the balustrade glass we recommend you have a rubber mallet, masking tape, craft knife or Stanley knife, a bottle of washing liquid and a spray bottle with water to hand.

  1. Align you glass panels and secure them in your chosen frameless balustrade fittings. If using the Mini Post systems we suggest you secure the panels but do not fully tighten the Tile-Lock system until the handrail is installed.
  2. Measure your run requiring the handrail. Use this measurement to cut the 12mm glass gasket supplied, but we suggest you over-size the gasket length as this can be trimmed after installation.
  3. Place the gasket over the top of the balustrade glass. Use small strips of masking tape to secure the gasket in place to make sure it does not move away from the top of the glass.
  4. Place some washing up liquid inside the slotted profile of the handrail. Use your finger to evenly spread this out along the length of the handrail.
  5. Spray a bit of water from a spray bottle over the full length of gasket that is on top of the glass.
  6. Starting from one end, press the handrail down over the gasket, pushing hard to secure the rail on top of the glass. Use the rubber mallet to persuade the handrail down onto the glass. Reasonable force can be applied by tapping the rail hard so it settles evenly on the glass along the full length of the run. You can always use a piece of corrugated card to protect the rail while firmly hitting the rail top with the mallet, to prevent marking the rail.
  7. Use the supplied adhesive to attach the end caps or elbows in place, or use the wall flanges to secure the rail back to the wall.
  8. Run a Stanley or craft knife under the rail to trim off any access rubber gasket and masking tape that is visible, and trim the length of the oversized gasket to size.
  9. Wipe down the rail using the stainless steel care kit, to clean any residue washing liquid or adhesive from the rail.
  10. Clean your glass panels using the glass care kit to remove any washing liquid and finger prints from the glass.
  • 24 Hrs Shipping

    On Selected Goods
  • Instant Quote

    Turn Your Ideas Into Reality
  • 100% Secure

    Secured By Sagepay

Product Reviews

There are no reviews yet.

Be the first to review “Slotted Mini Rail 12mm Glass”

Your email address will not be published. Required fields are marked *